![]() Please also visit our Web Site at for assistance. Installer must make sure the LCD Wall Mount is properly and securely attached and that appropriate fasteners are used. It is the responsibility of the installer to verify that the mount is anchored properly to the wall. THE MOUNT MUST BE ATTACHED TO WOOD STUDS OR TO PROPERLY INSTALLED ANCHORS IN CONCRETE. DO NOT MOUNT ONLY TO DRYWALL.īefore installing, check to make sure all parts of the mount are included. Make sure all screws and bolts are tightened before allowing Wall Mount to bear the full weight of the LCD Display. Elexa consumer products level mount full# Locate a proper place to mount by using a quality stud finder. It is recommended that the center of the stud be used – and that a nail be used to verify that a stud has been located. The mount requires a minimum of two studs to ensure proper and safe installation. The tilt arms will adjust horizontally to the right and left up to 8 inches after you determine the desired viewing location. ![]() If you are attaching the mount to concrete please skip to step 4.Ĭaution: Do not disassemble mount. Images of wall plate are shown for clarity of screw locations. Once the Wall Plate is in the correct position on the studs, screw 1 Hex Screw and 1 Hex Washer into the upper left mounting hole of the Wall Plate into the stud. Do not screw too tight until after all the screws are in. Using the Bubble Level as your guide, drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate. ![]() Now tighten both screws, proceed to drive the remaining 6 screws into the studs.Īll hex screws will require 1/8 inch pilot holes. NOTE: Due to the weight of the LCD/Plasma TV’s, it is necessary to mount the Wall Plate to at least 2 studs. Place the Wall Plate at the height you want to install the Flat Panel wall Mount. Elexa consumer products level mount install# Mark the eight holes you will be using for concrete anchors. Utilize the built-in bubble level to ensure proper mounting. Drill holes for the concrete anchors using an electric drill with a masonry bit (1/2’’ or 12mm). ![]() Drill into the wall at least as deep as the screw is long (3 inches). Insert all anchors into the holes and set them flush to the wall by tapping them in with a hammer. Once the Wall Plate is in the correct position on the wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer in the upper left mounting hole of the Wall Plate. Do not screw too tight until all the screws are in. Selecting the Appropriate Hardware for your Flat Panel.Drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate, then proceed to drive the remaining 6 screws into the concrete anchors. Select bolts from Bags 1-4, which most resemble the holes in the back of your Flat Panel. Thread the bolts carefully into your Flat Panel by hand to determine which provided mount hardware (correct diameter) is appropriate for installation.ĬAUTION: If you feel resistance, remove the bolt immediately and try another size! Next determine the correct length of the required bolt as described in the step 7. NOTE: You will not use all of the hardware included. If you have an oversized Flat Panel TV, you may need to use the Extension Arms provided. If you need to use the Extension Arms, you must use all Extensions Arms in order for the Mount to properly hold your TV. It is recommended to measure the distance between the mounting holes on the back of your TV prior to attaching the Extension Arms. The multiple hole pattern on the Extension Arms make it easy to adjust to fit your unique televisionĪttach the Extension Arms to the Tilt Arms by threading the M5 bolts into the provided Lock Washer, through the Extension Arm, through the Tilt Arms and tighten with the provided Hex Nut. Elexa consumer products level mount tv#Īttaching Mounting Arms to a TV with a Flat Back.2 M5 bolts must be used per Extension Arm. NOTE: NEVER LAY YOUR TELEVISION FACE DOWN ON ITS GLASS. Laying the television down on the glass may cause permanent damage. Plasma/LCDs TVs with a flat back panel will require a shorter bolt. Elexa consumer products level mount tv#įor a flat back Plasma/LCD that required a M4 or M5 diameter bolt, thread an M4 or an M5 bolt through the appropriate Lock Washer, an M4/M5 Washer, the Tilt Arm and into the TV.Elexa consumer products level mount full#.Elexa consumer products level mount install#.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |